Hysteresis vs. Eddy-Current vs. Regenerative Dynamometer
How the three main motor dynamometer types work, where each one fits, and how to choose the right one for your motors.
A hysteresis dynamometer gives smooth, precise load from zero speed and suits small motors up to a few kilowatts. An eddy-current dynamometer absorbs high power at high speed but produces little torque at low speed. A regenerative (AC) dynamometer can both brake and drive the motor in all four quadrants and returns the absorbed energy to the grid, which makes it the standard choice for efficiency certification, EV drives and high-power testing.
What a Dynamometer Does
A motor dynamometer applies a controlled load to the motor under test and measures the torque and speed at the shaft. Combined with electrical power measurement, that gives output power and efficiency at every operating point. The three technologies in this article differ in how they create the load, what happens to the absorbed energy, and how they behave at low and high speed.
Hysteresis and eddy-current dynamometers are absorbing dynamometers. They can only brake the motor, and they turn the absorbed power into heat. A regenerative dynamometer is an electric machine with its own drive, so it can brake or drive, and it feeds the absorbed power back into the supply.
How a Hysteresis Dynamometer Works
A hysteresis dynamometer has a rotor made of a special magnetic alloy that turns inside a pole structure with a field coil. When current flows through the coil, the rotor material is magnetized and re-magnetized as it rotates. The energy lost in that magnetic cycle produces a braking torque.
The key property is that hysteresis torque depends on the coil current, not on speed. The dynamometer delivers its torque from standstill up to its maximum speed, with no contact between rotor and stator and nothing to wear out. That makes it very smooth and repeatable, which is why hysteresis dynamometers are the classic choice for small motors.
Strengths
- Full torque at zero and low speed, so locked-rotor and stall tests are possible
- Smooth, contactless loading with very low torque ripple from the dynamometer itself
- Low rotor inertia, which suits small and fast motors
- Simple installation, no grid connection or water cooling required for most sizes
Limitations
- All absorbed power becomes heat in the rotor, so continuous power is limited, typically to a few kilowatts
- It can only brake, not drive the motor, so generator-mode tests are not possible
- Long tests at high power need pauses or derating to let the unit cool
Typical uses: micro motors, stepper and BLDC motors, small servo and gear motors, fans, pumps and actuators, in R&D labs and quality control. The 4Q-FHD range, for example, covers 500 mNm to 10 Nm, speeds up to 20,000 rpm and continuous power from 200 W to 3 kW.

How an Eddy-Current Dynamometer Works
An eddy-current dynamometer uses a conductive rotor, usually a toothed steel disc, turning in a magnetic field created by excitation coils. The moving rotor induces eddy currents in the surrounding material, and those currents create a braking torque. The energy ends up as heat, removed by air or, more often at higher power, by cooling water.
Because eddy currents depend on the rate of change of the field, the braking torque rises with speed. At standstill an eddy-current dynamometer produces practically no torque, and at low speed its capacity is small. At medium and high speed it absorbs large amounts of power in a compact unit, which is why it is widely used for engines and larger motors.
Strengths
- High absorbed power and high speed capability for the size and cost
- Robust, with a long track record in engine and drivetrain testing
- Fast torque control through the excitation current
Limitations
- Little or no torque at low speed, so stall, locked-rotor and low-speed tests are difficult
- Absorb-only: no motoring, no generator-mode testing, no drive-cycle simulation with negative torque
- All test energy is wasted as heat, which raises cooling needs and running costs on long tests
Typical uses: combustion engine testing, endurance testing of medium and large motors where low-speed behaviour is less important, and budget-sensitive high-speed absorption.
How a Regenerative Dynamometer Works
A regenerative dynamometer is an AC machine, typically an induction or permanent magnet motor, controlled by a bidirectional drive. When it brakes the motor under test, it works as a generator and its drive returns the energy to a common DC bus or to the grid. When needed, the same machine can drive the test motor, for example to measure generator behaviour, back-EMF or friction.
This is called four-quadrant operation: braking and driving, in both directions of rotation. In a 4Q Systems platform the motor under test and the load machine share a common DC bus, so power circulates between them and the grid supplies only the losses. Up to 92% of the test energy is recovered. More detail is in Regenerative Dynamometer Explained.
Strengths
- Full torque from zero speed to maximum speed, in both directions
- Can drive as well as brake, so motoring, generating and drive-cycle tests run on one bench
- Energy recovery keeps electricity and cooling costs low, even for long tests at high power
- Fast dynamic response for servo, EV and transient testing
- Scales from small machines to hundreds of kilowatts
Limitations
- Higher initial cost and more complex than an absorbing brake of the same power
- Needs a suitable grid connection and power electronics
- For very small motors, a hysteresis dynamometer is usually simpler and more economical
Typical uses: IEC 60034-2-1 efficiency certification (4Q-MEPS), EV traction motors and e-axles (4Q-eDrive), servo motors (4Q-SMTS), and any lab that runs long or high-power tests.


Side-by-Side Comparison
| Hysteresis | Eddy-current | Regenerative (AC) | |
|---|---|---|---|
| Torque at zero speed | Full torque | Practically none | Full torque |
| Torque vs. speed | Nearly constant | Rises with speed | Controlled over the full range |
| Typical power | Watts to a few kW | kW to hundreds of kW | Under 1 kW to hundreds of kW |
| Can drive the motor | No | No | Yes, four-quadrant |
| Absorbed energy | Heat | Heat (often water-cooled) | Returned to the grid |
| Long tests at full load | Limited by heating | Possible, high cooling load | Yes, low running cost |
| Dynamic response | Good | Good at speed | Very fast |
| Initial cost | Low | Low to medium | Higher |
| Best for | Small motors, R&D and QA | Engines, high-speed absorption | Certification, EV, servo, high power |
Values are typical for each technology. Individual products vary.
How to Choose
Four questions settle most decisions:
- How large is the motor? Below about 10 Nm and a few kilowatts, a hysteresis dynamometer is usually the most practical choice. Above that, regenerative systems take over.
- Do you need torque at low speed? Stall, locked-rotor and low-speed efficiency tests rule out eddy-current dynamometers.
- Do you need to drive the motor? Generator-mode tests, back-EMF measurement, regenerative braking and drive cycles with negative torque require a regenerative dynamometer.
- How long and how hard will you run it? Efficiency maps, temperature-rise tests and endurance runs at high power are where energy recovery pays back the higher purchase price.
Many labs end up with two technologies: a hysteresis dynamometer for small motors and a regenerative system for everything above it, both running the same software. See all 4Q platforms side by side on Motor Testing Systems.
Frequently Asked Questions
Is a hysteresis dynamometer accurate enough for efficiency testing?
Yes, for small motors. Accuracy depends mainly on the torque measurement and the power analyzer, not on the braking principle. The limit is power: once the motor’s output exceeds what the dynamometer can dissipate as heat, a regenerative system becomes the better choice.
Can an eddy-current dynamometer test an EV motor?
Only partly. It can absorb power at medium and high speed, but it cannot load the motor near standstill, cannot drive it, and cannot simulate regenerative braking. Full EV motor and inverter validation needs a four-quadrant regenerative dynamometer such as 4Q-eDrive. See also What Is an E-Drive Test Bench?
Which dynamometer is required for IEC 60034-2-1?
The standard defines test methods and measurement accuracy, not a dynamometer type. In practice, certification labs use regenerative dynamometers, because the load tests and temperature-rise tests run at full load for long periods. Regeneration keeps those tests affordable and the lab cool.
What about powder brakes and water brakes?
Magnetic powder brakes are absorbing brakes that give high torque at low speed, but the powder wears and they are less suited to precise, repeatable measurement. Water brakes absorb very high power and are mainly used for large engines. Neither can drive the motor or recover energy.
Not Sure Which Dynamometer Fits Your Motors?
Tell us your motor type, torque and speed range, and the tests you need to run. Our engineers will recommend the right platform.









